Winter NAMM 2013 - G&L/ BBE

[Craig]

Hi All,

We got back from our NAMM trip yesterday late afternoon.

After two years of not having a booth at NAMM, BBE/G&L returned to Anaheim and this time shared a booth with Rivera Amps.

Here's what the BBE/G&L booth looked like:






Here's the run down on the new G&L instruments:

Guitars:



ASAT Classic Bluesboy 90
Same as ASAT Classic Bluesboy, except features G&L P-90 pickup in neck position.



ASAT Classic 'S' Alnico
Same as ASAT Classic , except features a contured arm and rear body, reverse-wound
Legacy middle pickup and 5-way pickup selector with push/pull expansion switch enabling
additional pickup combinations of neck+bridge or all 3 pickups together. Same as ASAT Classic 'S',
except features G&L Alnico single coil pickups.

ASAT Classic Solamente (Not shown)
Same as ASAT Classic, except has no neck pickup and has a 3-way selector circuit by Paul Gagon.

ASAT Classic Solamente Alnico (Not shown)
Same as ASAT Classic Alnico, except has no neck pickups and has a 3-way selector circuit by Paul Gagon.



Fallout
SC-2 body with a custom pickguard and G&L P-90 in neck position, Seymour Duncan JB Humbucker in
bridge position, 3-way pickup selector, volume tone and G&L Saddle-Lock bridge (no Dual Fulcrum option).



Superhawk Jerry Cantrell Signature Model
Finish: Black, Ivory, Whiskey
Body: Soft Maple
Neck: #4 Custom Profile Hard Rock with ebony fingerboard, medium jumbo frets
Pickups: Seymour Duncan 59 Humbucker in neck position, JB Humbucker in bridge position
Controls: 3-way pickup selector, volume, tone
Bridge: G&L Saddle Lock
Tuners: Non-locking tuners
Other: Black hardware, paint-matched headstock, shielded control cavity



Superhawk Deluxe Jerry Cantrell Signature Model
Same as Superhawk Jerry Cantrell Signature Model but features:
Finish: Blueburst or Blackburst
Body: Premium flamed Maple top on Soft Maple

Basses:



ASAT Bass Tom Hamilton Signature Model
Finish: Choice of Blue, Turquoise, or Red Metal Flake finish with Silver faux double -binding
Body: Western Sugar Pine
Neck: #8 Quarterswan Maple with matching fingerboard, light tint satin finish
Pickups: 2 G&L Magnetic Field Design "Hamitone" humbuckers
Controls: G&L Tri-Tone active/passive electronics, 3-way mini-toggle pickup selector,
series/parallel mini-toggle, preamp control min-toggle (off/on/on with high end EQ boost),
volume, treble, bass
Bridge: G&L Saddle Lock
Tuners: G&L Utralite tuners with aluminum tapered string posts



LB-100 (G&L Split-Coil Alnico V pickup)
Body: Alder on Standard and all solid finishes, Swamp Ash on all Premier finishes
Neck: #12 Hard Rock Maple neck with Rosewood or Maple fingerboard, medium jumbo frets
Pickups: G&L Split-Coil Alnico V pickup
Controls: volume, tone
Bridge: G&L Saddle Lock
Tuners: G&L Utralite tuners with aluminum tapered string posts
Pickguard: 3-ply white



MJ-4
Finish: Standard finishes included
Body: Alder on Standard and all solid finishes, Swamp Ash on all Premier finishes
Neck: #12 Hard Rock Maple neck with Rosewood or Maple fingerboard, medium jumbo frets
Pickups: 2 G&L Bi-Coil Alnico V jazz pickups
Controls: G&L M-Series 18V active preamp, pan, volue, and 3-band EQ featuring
center detents
Bridge: G&L Saddle Lock
Tuners: G&L Utralite tuners with aluminum tapered string posts

This is the most instruments I have seen G&L announce and release at one time.

On the BBE side:

Stomp Boxes - Winter/Spring 2013 Line

427 FD-427P
Blacksmith BD-69
Boosta Grande BG-20
G Screamer OG-1
Mind Bender MB-2
OptiComp OC-5
Sonic Stomp SS-92
Soul Vibe SV-74
Tremor TR-63B
Two Timer TT-2
VariComp VC-3080
SupaCharger
Windowpane WP-69
Wah

See this link for specs and photos.

Later, I will be posting more photos in the Gallery.

[darwinohm]

I'm really liking this and I am afraid to ask. Does the Tom Hamilton Asat bass come in a 5 string?? I am afraid to get the answer. The addition of a p90 on some of these Asats is awesome, and the Alnico choices. I am impressed!!-- Thanks for posting Craig and looking forward to the rest!-- Darwin

[ChinoGee]

Thansk a lot Craig!

Fallout
SC-2 body with a custom pickguard and G&L P-90 in neck position, Seymour Duncan JB Humbucker in
bridge position, 3-way pickup selector, volume tone and G&L Saddle-Lock bridge (no Dual Fulcrum option).

I like very much this model, the sound should be great!

Is the "Fallout" a new model? Which is the price?

[willross]

The ASAT Classic Solamente Alnico sounds interesting. Is it like a 59 Esquire?


Cheers,

Will

[yowhatsshakin]

Here's the run down on the new G&L instruments:

Guitars:

...

ASAT Classic Solamente (Not shown)
Same as ASAT Classic, except has no neck pickup and has a 3-way selector circuit by Paul Gagon.

ASAT Classic Solamente Alnico (Not shown)
Same as ASAT Classic Alnico, except has no neck pickups and has a 3-way selector circuit by Paul Gagon.

Well how about that sport fans? Tim's ASAT '50 finally has finally led to an official release of a single pup ASAT! And make that two at that. Love to see some pics and learn some about the details of the tone circuit (and how it compares/differs versus the ASAT '50). Very excited about these models as well as the Alnico 'S'

- Jos

P.S. Great to see soft maple as the body wood for the Cantrell models!

[darwinohm]

The Fallout looks like a take off on the GBLE-II to me. -- Darwin

[Goat]

That was my first thought Darwin. They must like the forum's ideas so far... I'm liking the creme pickguards on those; might look nice with a lemon top.

[RampageFan]

Thanks for posting the pictures and the update Craig! Very much appreciated!

I'm very impressed with the new designs and pickup options. The Fallout looks very interesting. I've been lurking on other manufacturers forums, and there are people very angry over the direction other companies are going in. Seems to me like G&L is very focused right now.

And the Superhawk! I will be the first in line for the Deluxe Blueburst model! I'm digging the Superhawk with the saddle lock bridge!

Dave

[elduave]

Thanks for posting!

[JagInTheBag]

The Fallout looks like a take off on the GBLE-II to me. -- Darwin

LMAO! The LE-2 is a take off on the Fallout. We were able to modify a G&L to GbL specs before it was even released! How cool is that?!

[Goat]

The Fallout looks like a take off on the GBLE-II to me. -- Darwin

LMAO! The LE-2 is a take off on the Fallout. We were able to modify a G&L to GbL specs before it was even released! How cool is that?!

I wonder if it will bring the price of the GbL LE2 down at all as the machining will be semi set up for it....?

[darwinohm]

My take would be the request for GBLE-2 was an indication that there could be a demand for the SC-2 body in a different configuration. After looking into it, I would bet the idea was picked up because there is no design changes other than some routing. What a way to breath new life in the SC platform. Goat, I wouldn't bet on a big price break but it certainly makes sense for G&L to test this new configuration on an old platform. I think that is smart marketing for G&L and they just may be listening to what their guitar owners are saying. Just my opinion. As a final thought, I think a P90 in the neck position of the LE2 would be just sweet -- Darwin

[JagInTheBag]

The Fallout looks like a take off on the GBLE-II to me. -- Darwin

LMAO! The LE-2 is a take off on the Fallout. We were able to modify a G&L to GbL specs before it was even released! How cool is that?!

I wonder if it will bring the price of the GbL LE2 down at all as the machining will be semi set up for it....?

The Fallout is not simply a code alteration of the SC-2. They had to start from scratch to make the fallout because of how the SC was originally programmed.

They actually threw in ADDITIONAL machining, fixturing, and CNC programming so we can make the LE-2.

The LE-2 has a dual fulcrum bridge (Fallout does not have it). I've also been told that the overall high of the DF is lower on this model and the neck pocket is deeper, giving the whole thing a better feel compared to a DF equipped SC-2- which has a "stuck-on" appearance.

The LE-2 has unique pickup routes for neck and bridge.

The LE-2 has a unique pick guard that is not swappable between the two models.

So, really they are subsidizing the development of the LE-2 with the development of the Fallout.

No to mention that the LE-2 will be the first limited edition G&L to feature a roasted maple neck.

[willross]

The Fallout looks like a take off on the GBLE-II to me. -- Darwin

LMAO! The LE-2 is a take off on the Fallout. We were able to modify a G&L to GbL specs before it was even released! How cool is that?!

I wonder if it will bring the price of the GbL LE2 down at all as the machining will be semi set up for it....?

The Fallout is not simply a code alteration of the SC-2. They had to start from scratch to make the fallout because of how the SC was originally programmed.

They actually threw in ADDITIONAL machining, fixturing, and CNC programming so we can make the LE-2.

The LE-2 has a dual fulcrum bridge (Fallout does not have it). I've also been told that the overall high of the DF is lower on this model and the neck pocket is deeper, giving the whole thing a better feel compared to a DF equipped SC-2- which has a "stuck-on" appearance.

The LE-2 has unique pickup routes for neck and bridge.

The LE-2 has a unique pick guard that is not swappable between the two models.

So, really they are subsidizing the development of the LE-2 with the development of the Fallout.

No to mention that the LE-2 will be the first limited edition G&L to feature a roasted maple neck.

Nice! I can't wait & will pick up a roasted maple ASAT Solamente too...


Cheers,

Will

[darwinohm]

Jag, that is good information but I would question DF statement. How would they lower it without a DF redesign?

The LE-2 has a dual fulcrum bridge (Fallout does not have it). I've also been told that the overall high of the DF is lower on this model and the neck pocket is deeper, giving the whole thing a better feel compared to a DF equipped SC-2- which has a "stuck-on" appearance.

I think the DF on my SC-2 is no different in height than a Legacy or an ASAT with a DF. It looks very well appointed. -- Darwin

[JagInTheBag]

Jag, that is good information but I would question DF statement. How would they lower it without a DF redesign?

The SC NECK is higher, thusly the DF sits higher to accommodate. The neck pocket is deeper on the Fallout, so the DF is also lower- these words are from Darth, I am just the messenger.

[darwinohm]

Thanks Jag. I was just curious.-- Darwin

[JagInTheBag]

Thansk a lot Craig!

Fallout
SC-2 body with a custom pickguard and G&L P-90 in neck position, Seymour Duncan JB Humbucker in
bridge position, 3-way pickup selector, volume tone and G&L Saddle-Lock bridge (no Dual Fulcrum option).

I like very much this model, the sound should be great!

Is the "Fallout" a new model? Which is the price?

SO much better looking than a Mustang or any variant

[Craig]

Thansk a lot Craig!

Fallout
SC-2 body with a custom pickguard and G&L P-90 in neck position, Seymour Duncan JB Humbucker in
bridge position, 3-way pickup selector, volume tone and G&L Saddle-Lock bridge (no Dual Fulcrum option).

I like very much this model, the sound should be great!

Is the "Fallout" a new model? Which is the price?

Yes, the Fallout is a new model, as are the others I listed here.
MAP for the Fallout is $1050.

[Craig]

Nice! I can't wait & will pick up a roasted maple ASAT Solamente too...

Cheers,

Will

The Roasted Maple neck is not a standard option on any model. You should
check with your dealer and see if they can special order it. The ones on the
prototypes were just trials and AFAIK G&L has not added them as an option.

[JagInTheBag]

Yes, the Fallout is a new model, as are the others I listed here.
MAP for the Fallout is $1050.

Do we know what the standard features and colors that are available on it?

[Craig]

Yes, the Fallout is a new model, as are the others I listed here.
MAP for the Fallout is $1050.

Do we know what the standard features and colors that are available on it?

From the January 1, 2013 US Price List:

Finish: Standard finishes included
Body: Alder on Standard and all solid finishes, Swamp Ash on all Premier finishes
Neck: #1 Hard Rock with Rosewood or Maple fingerboard, medium jumbo frets
Pickups: G&L P-90 in neck position, Seymour Duncan JB Humbucker in bridge position
Controls: 3-way pickup selector, volume, tone
Bridge: G&L Saddle Lock (no Dual Fulcrum option)
Tuners: Non-locking tuners

[Craig]

I'm really liking this and I am afraid to ask. Does the Tom Hamilton Asat bass come in a 5 string?? I am afraid to get the answer. The addition of a p90 on some of these Asats is awesome, and the Alnico choices. I am impressed!!-- Thanks for posting Craig and looking forward to the rest!-- Darwin

Sorry Darwin, no 5 string option is available on the ASAT Bass models.

[ChinoGee]

Thanks a lot Craig! The Fallout has a cool price for a USA made G&L, especially the pups. When will it be available for order?

[Craig]

Thanks a lot Craig! The Fallout has a cool price for a USA made G&L, especially the pups. When will it be available for order?

AFAIK, the new models can be ordered now or shortly after your dealer receives the U.S. Dealer Price List Effective January 1, 2013.

[louis cyfer]

i don't think slapping some new pickups in current models is much of a progress. i can swap in an alnico pup into any g&l, and i already have the bluesboy with the p90. i am disappointed. i think some ergonomic changes like sculpted neck heel, maybe sculpted lower cutaway should have been included as options. also, making the nena finishes as options should be included.

finally they made a couple of smaller footprint pedals, although not small enough and not on enough of them.

[Goat]

....I think a P90 in the neck position of the LE2 would be just sweet -- Darwin

So do I. But I'm late to the party and haven't had any input.

I agree with Louis on the sculpted neck heel; long overdue. But generally I like what G&L are doing with the new models.

[blargfromouterspace]

Woohoo!! Solamente! I remember a post (Jag, probably from you via Dave) that G&L only intend to have the JC sig Rampage as the only one pickup guitar. Pretty stoked that they've decided to make one of these.

I love the look of the new BBE pedals too. The graphics on the old ones were awful.

[NickHorne]

The Asat Classic 90 is fantasy come true. GREAT idea.
When can we get one?

[willross]

Nice! I can't wait & will pick up a roasted maple ASAT Solamente too...

Cheers,

Will

The Roasted Maple neck is not a standard option on any model. You should
check with your dealer and see if they can special order it. The ones on the
prototypes were just trials and AFAIK G&L has not added them as an option.

That's ok. If we can get it for the LE-2 I'm grateful... I also have NO experience with that type of neck, so one at a time to "test the waters".


Cheers,

Will

[meowmix]

Thanks for posting the pictures and the update Craig! Very much appreciated!

I'm very impressed with the new designs and pickup options. The Fallout looks very interesting. I've been lurking on other manufacturers forums, and there are people very angry over the direction other companies are going in. Seems to me like G&L is very focused right now.

And the Superhawk! I will be the first in line for the Deluxe Blueburst model! I'm digging the Superhawk with the saddle lock bridge!

Dave

Dave, I am curious, do any of your Rampages have 1 3/4" neck profile? If so, how does it play?
Thanks


The Jerry models say

Superhawk Jerry Cantrell Signature Model

Neck: #4 Custom Profile Hard Rock with ebony fingerboard, medium jumbo frets

[Craig]

The Asat Classic 90 is fantasy come true. GREAT idea.
When can we get one?

See this previous post.

[NickHorne]

Great. And ThankYou!

[RampageFan]

Dave, I am curious, do any of your Rampages have 1 3/4" neck profile? If so, how does it play?
Thanks


The Jerry models say

Superhawk Jerry Cantrell Signature Model

Neck: #4 Custom Profile Hard Rock with ebony fingerboard, medium jumbo frets

Yes, all of my Rampages have the 1 3/4" neck. I actually prefer them. They feel natural to me. I had a Jackson Soloist with the thin, compound radius neck, and after playing G&L again, it didn't feel right to me anymore so I sold it.

Hope this helps,
Dave

[Craig]

I've added photos to the 2013 Winter NAMM Show Album in the Gallery.

[blargfromouterspace]

Any idea if the Solamente is routed for a neck pickup? Not that I intend to install one, just curious as to whether it is just the pick guard and wiring making the difference between it and a normal Classic. Could be very cool and totally minimalist (is that an oxymoron?) without a pick guard.

[JagInTheBag]

What do you all think of the headstock on the Fallout?

[willross]

Could be very cool and totally minimalist (is that an oxymoron?) without a pick guard.

That is a great idea! For the most part, the pickguard is an affectation...


Cheers,

Will

[blargfromouterspace]

What do you all think of the headstock on the Fallout?

I'd have preferred the ASAT font as found on the ASAT Special and on the larger headstock too. To be totally honest that model is doing absolutely nothing for me. It looks cluttered. The pickups are far too big for it. I'm sure it would a great guitar to play, but visually its lacking. And I don't think they've chose the best colour schemes to show it off either. JMO, YMMV etc etc.

[Ahryn]

This solamente intrigues me....
And the Fallout looks very hip, lots of new models

Can't wait to see more pics to drool over

[Craig]

Dave is starting to get the new models added to the main G&L website.

Here's the two (make that three!):

MJ-4 bass
ASAT® Classic 'S' Alnico and ASAT® Classic 'S' Alnico Launch Edition

Check them out.

[Craig]

Any idea if the Solamente is routed for a neck pickup? Not that I intend to install one, just curious as to whether it is just the pick guard and wiring making the difference between it and a normal Classic. Could be very cool and totally minimalist (is that an oxymoron?) without a pick guard.

Hi Jamie,

I checked with Dave about this. Here's what he said:

We went back and forth about the route, and in the end we decided to leave it there. Some owners may want to end up
with a two pickup guitar so we've left them the option. It was a compromise, really. We'd prefer to have left the wood in
there to continue the mass from the heel to the boxed bridge and pickup, but thoughts of long term ownership swayed us.

Hope this helps.

[Craig]

What do you all think of the headstock on the Fallout?

From Dave:

It is a slimmed down version of the large mid-'80s headstock as on SC-2/Rampage/Superhawk etc. It is not derived from the ASAT at all.

I think it matches better with the size of the body.

[blargfromouterspace]

Any idea if the Solamente is routed for a neck pickup? Not that I intend to install one, just curious as to whether it is just the pick guard and wiring making the difference between it and a normal Classic. Could be very cool and totally minimalist (is that an oxymoron?) without a pick guard.

Hi Jamie,

I checked with Dave about this. Here's what he said:

We went back and forth about the route, and in the end we decided to leave it there. Some owners may want to end up
with a two pickup guitar so we've left them the option. It was a compromise, really. We'd prefer to have left the wood in
there to continue the mass from the heel to the boxed bridge and pickup, but thoughts of long term ownership swayed us.

Hope this helps.

Bugger. Thats a legitimate enough reason though, there are people who have 'stealth' neck pickups hidden under the pick guard in that type of guitar. Think I'll just make my own Solamente tomorrow and see how it goes.

Thanks for checking it out Craig, much appreciated.

[NickHorne]

All great stuff, + good to see so many.

I'm still hoping for the "Hellesquire" one day! A saddlelock Asat with just a back pickup, the Will Ray overwound Z-unit, mounted however it works best. Wouldn't that be fun ?