View unanswered posts | View active topics It is currently Thu Mar 28, 2024 2:23 am




Reply to topic  [ 6 posts ] 
 Stripped hex screw for saddle lock bridge -- advice? 
Author Message

Joined: Mon Oct 06, 2014 8:42 am
Posts: 36
Location: Oakland, CA
Post Stripped hex screw for saddle lock bridge -- advice?
Hi, one of the hex sockets for the saddle height adjustment is stripped. It's on an '83 SC-2, and the G&L site currently recommends replacing the entire bridge assembly, as the modern saddles are too wide for the old bridge. Anyone know where I can get a replacement saddle? Or a way to extract and replace the height adjustment screws?

Thanks


Mon Oct 30, 2017 3:30 pm
Profile
User avatar

Joined: Thu Feb 17, 2011 7:18 pm
Posts: 2344
Location: None of the above
Post Re: Stripped hex screw for saddle lock bridge -- advice?
I've done the same thing before. Extraction is easy during a string change or with the string loosened all the way. Just back out the locking set screw beside the high E saddle, and then back the intonation screw out of the affected saddle so that it can be removed from the bridge. You should be able to remove the stripped height adjustment screw from underneath with your fingers or a set of pliers. If you don't want to replace the screw, you could probably adjust it from below with a bit of trial and error. That's what I've done with a stripped height adjuster on an F-100.

I am not sure what the original spec was for those screws, other than guessing they would not have been metric. If anybody here knows the spec, I would love to hear it.

Ken


Mon Oct 30, 2017 7:17 pm
Profile
User avatar

Joined: Sun Apr 20, 2014 3:52 am
Posts: 943
Location: Delaware
Post Re: Stripped hex screw for saddle lock bridge -- advice?
0.05 inch is what i use on my 80's G&L's for the saddle height adjustment.
it's the smallest allen wrench from stew-mac in the English set

_________________
john o


Mon Oct 30, 2017 7:25 pm
Profile

Joined: Mon Oct 06, 2014 8:42 am
Posts: 36
Location: Oakland, CA
Post Re: Stripped hex screw for saddle lock bridge -- advice?
I was able to use a plier to back out the screws, worked some WD-40 into the saddle and stuffed a small wire brush down in there. The screws still don't want to move past a position, so I think the threads on the inside of the saddle are stripped. :-(


Tue Oct 31, 2017 10:24 am
Profile
User avatar

Joined: Tue Dec 20, 2016 9:08 am
Posts: 579
Location: Canada
Post Re: Stripped hex screw for saddle lock bridge -- advice?
One trick, and you're probably past this point, is to use crazy glue to attach the hex key to whatever end is protruding. Depending on how good a bond you get, you may be able to unscrew it /pull it out that way.

_________________
G & L: '08 Comanche (Tribute) | '14 ASAT Classic | '00 ASAT Spec | '21 JB2 (Tribute)
Other: '87 Strat | '05 Heritage CH-157 | '12 Tele Select Koa | '19 MJT Esquire | '18 Taylor | 2015 Chrome Epi Dobro |


Tue Oct 31, 2017 10:59 am
Profile WWW
User avatar

Joined: Sat Jan 07, 2012 11:46 pm
Posts: 1632
Location: Grayslake, IL
Post Re: Stripped hex screw for saddle lock bridge -- advice?
scelerat wrote:
I was able to use a plier to back out the screws, worked some WD-40 into the saddle and stuffed a small wire brush down in there. The screws still don't want to move past a position, so I think the threads on the inside of the saddle are stripped. :-(



If you have enough to grab onto, try a pair of needle nose vice grips to get it turned past the tough spot. Then, go the hardware store with the old set screw, match the pitch and diameter and also get a small tap set if you don't have one. Run a tap through the saddle to clean up or recut the treads and use your new set screw. Ace Hardware (if they exist near you) has most every imaginable screw. If you need to use a modern one, which is larger, then just tap the saddle out to the larger size.


Tue Oct 31, 2017 12:30 pm
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware.